Open Access
Issue
MATEC Web Conf.
Volume 190, 2018
5th International Conference on New Forming Technology (ICNFT 2018)
Article Number 01003
Number of page(s) 7
Section Keynotes
DOI https://doi.org/10.1051/matecconf/201819001003
Published online 18 September 2018
  1. Geigerl M, Kleine M, Eckstein R, Tieslerl N, Engel U. Microforming. CIRP Ann 2001; 50(2): 445-462. [Google Scholar]
  2. Engel U, Eckstein R. Microforming-from basic research to its realization. J Mater Process Tech (2002); 125-126: 35-44. [CrossRef] [Google Scholar]
  3. Kals TA, Eckstein R. Miniaturization in sheet metal working. J Mater Process Tech, 103: (2000), 95-101. [CrossRef] [Google Scholar]
  4. Suzuki K, Matsuki Y, Masaki K, Sato M, Kuroda M. Tensile and microbend tests of pure aluminum foils with different thicknesses. Mater Sci Eng A (2009), 513–514: 77-82. [Google Scholar]
  5. Diehl A, Engel U, Merklein M. Size effects in bending processes applied to metal foils. Prod Eng Res Devel, (2010); 4: 47-56. [CrossRef] [Google Scholar]
  6. Li HZ, Dong XH, Shen Y, Diehl A, Hagenah H, Engel U, Merklein M. Size effect on springback behavior due to plastic strain gradient hardening in microbending process of pure aluminum foils. Mater Sci Eng A (2010); 527: 4497-4504. [CrossRef] [Google Scholar]
  7. Li HZ, Dong XH, Wang Q, Shen Y, Diehlc A, Hagenah H, Engel U, Merklein M. Determination of material intrinsic length and strain gradient hardening in microbending process. Int J Solids Struct (2011); 48: 163–174. [CrossRef] [Google Scholar]
  8. Aoyama T, Shimizu T, Zheng Q, Yang M. Effect of Heating on Springback in Heat Assisted Microbending. Adv Mater Res (2014); 939: 409-414. [CrossRef] [Google Scholar]
  9. Vollertsen F, Biermann D, Hansen HN, et al. Size effect in manufacturing of metallic components. CIRP Ann 2009; 58: 566-87. [CrossRef] [Google Scholar]
  10. M. YANG, “Fabrication of MEMS Using Micro Metal Forming Process”, Proc. ICNFT, (2004), pp.135-140. [Google Scholar]
  11. Engel, U., Tribology in Microforming. Wear, 260(2006), 265-273. [CrossRef] [Google Scholar]
  12. Grill, A., 1997. Tribology of diamond like carbon and related materials: an updated review. Surface and Coating Technology, 94–95(1997), 507–513. [CrossRef] [Google Scholar]
  13. Tetsuhide Shimizu, Tai Kakegawa, Ming Yang, Micro-texturing of DLC thin film coatings and its tribological performance under dry sliding friction for microforming operation, Procedia Engineering 81(2014), pp.1884 – 1889. [CrossRef] [Google Scholar]
  14. T. Kakegawa, T. Shimizu, Y. Sagisawa, M. Yang, Surface Texturing on Micro-Die and In-situ Observation of Its Dry Friction and Wear Behavior, J. of JSTP, 56-657(2016), 891-896. [Google Scholar]
  15. B. Eichenhueller,E. Egerer,U. Engel, Microforming at elevated temperature-forming and material behavior,The International Journal of Advanced Manufacturing Technology,33(2007), 119-124. [CrossRef] [Google Scholar]
  16. M. Yang, T. Shimizu, Novel processes and related technologies for micro metal forming, Int. J. Materials and Product Technology, Vol. 54, Nos. 1/2/3 (2017), 32-44. [CrossRef] [Google Scholar]
  17. H. Tanabe, M. YANG, Design and Evaluation of Heat Assisted Microforming System, Steel Research International, Special Edition (2011), 1020-1024. [Google Scholar]
  18. Qiu Zheng, Tetsuhide Shimizu, Ming Yang, Numerical Analysis of Temperature Distribution and Its Optimization for Thin Foils in Micro Deep Drawing Assisted by Resistance Heating, Steel Research International, 85 (2015), 1-8. [Google Scholar]
  19. Yang Bai, Kenji Nishikawa, Ming Yang, Metal Surface Modification with Vibration-Aided Micro-Forging, Materials Transactions, Vol. 53, No. 3 (2012) pp. 489-494. [CrossRef] [Google Scholar]
  20. Yang Bai, Ming Yang, Investigation on mechanism of metal foil surface finishing with vibration-assisted micro-forging, J. of Materials Processing Technology 213 (2013), pp.330– 336. [CrossRef] [Google Scholar]
  21. Hu, J., Shimizu, T., Yang, M., "Impact effect of superimposed ultrasonic vibration on material characteristics in compression tests." Procedia Engineering, (2017). [Google Scholar]
  22. T Shiratori, Y. Suzuki, S. Nakano, M. Yang, and T. Komatsu, Effects of grain size on the sheared surface in micropiercing of austenitic stainless steel SUS304, Manufacturing Rev., 2-9(2015), 1-6. [Google Scholar]
  23. M. Katoh et al., “Reduction of diffusion bonding temperature with recrystallization at austenitic stainless steel,” Tetsu-to-hagane, 102 (2016), 34-39. [CrossRef] [Google Scholar]
  24. T. Shiratori, S. Nakano, M. Katoh, Y. Suzuki, T. Aihara, M. Yang, Development of metal MEMS manufacturing technologies using pierced metal foil and diffusion bonding process at low temperature, Proc. 4M/IWMF, (2016). [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.