Open Access
| Issue |
MATEC Web Conf.
Volume 406, 2024
2024 RAPDASA-RobMech-PRASA-AMI Conference: Unlocking Advanced Manufacturing - The 25th Annual International RAPDASA Conference, joined by RobMech, PRASA and AMI, hosted by Stellenbosch University and Nelson Mandela University
|
|
|---|---|---|
| Article Number | 07011 | |
| Number of page(s) | 14 | |
| Section | AM Material and Part Characterisation | |
| DOI | https://doi.org/10.1051/matecconf/202440607011 | |
| Published online | 09 December 2024 | |
- K. V. Wong and A. Hernandez, “A Review of Additive Manufacturing,” International Scholarly Research Network, pp. 1-5, 17 June 2012. [Google Scholar]
- B. Jackson, K. Fouladi and B. Eslami, “Multi-Parameter Optimization of 3D Printing Condition for Enhanced Quality and Strength,” Polymers, pp. 1-13, 2022. [Google Scholar]
- ASTM, “D638-14: Standard Test Method for Tensile Properties of Plastics,” American Society for Testing and Materials (ASTM) International, West Conshohocken, 2015. [Google Scholar]
- ASTM, “D790-17: Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials,” American Society for Testing and Materials (ASTM) International, West Conshohocken, 2017. [Google Scholar]
- Y. S. Narayan and S. A. Kumar, “Tensile Testing and Evaluation of 3D-Printed PLA Specimens as per ASTM D638 Type IV Standard,” Lecture Notes in Mechanical Engineering, pp. 79-95, 2019. [Google Scholar]
- M. Eryildiz, “The Effects Of Infill Patterns On The Mechanical Properties Of 3D Printed PLA Parts Fabricated By Fdm,” Ukrainian Journal Of Mechanical Engineering And Materials Science, pp. 1-8, 2021. [Google Scholar]
- A. M. Forster, “Materials Testing Standards for Additive Manufacturing of Polymer Materials: State of the Art Standards Applicability,” National Institute of Standards and Technology, 2015. [Google Scholar]
- B. Goldschmidt, “All3DP,” All3DP, 20 October 2022. [Online]. Available: https://all3dp.com/2/cura-infill-patterns-all-you-need-to-know/. [Accessed 7 March 2023]. [Google Scholar]
- G. D. Goh, S. Agarwala, G. L. Goh, V. Dikshit, S. L. Sing and W. Y. Yeong, “Additive manufacturing in unmanned aerial vehicles (UAVs): Challenges and potential,” Aerospace Science and Technology, vol. 63, pp. 140-151, 2017. [CrossRef] [Google Scholar]
- F. M. Mwema and E. T. Akinlabi, “Basics of Fused Deposition Modelling (FDM),” in Fused Deposition Modeling Strategies for Quality Enhancement, Springer International Publishing, 2020, pp. 1-15. [Google Scholar]
- A. Malik, M. L. Ul Haq, A. Raina and K. Gupta, “3D printing towards implementing Industry 4.0: sustainability aspects, barriers and challenges,” Industrial Robot, vol. 49, no. 3, pp. 491-511, 2021. [Google Scholar]
- O. Lužanin, D. Movrin and M. Plancak, “Effect Of Layer Thickness, Deposition Angle, And Infill On Maximum Flexural Force In Fdm-Built Specimens,” Journal for Technology of Plasticity, vol. 39, no. 1, pp. 50-58, 2014. [Google Scholar]
- S. Raja, A. P. Agrawal, P. P. Patil, P. Thimothy, R. Y. Capangpangan, P. Singhal and M. T. Wotango, “Optimization of 3D Printing Process Parameters of Polylactic Acid Filament Based on the Mechanical Test,” International Journal of Chemical Engineering, pp. 1-7, 2022. [Google Scholar]
Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.
Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.
Initial download of the metrics may take a while.