Article references

Articles citing this article

The Citing articles tool gives a list of articles citing the current article.
The citing articles come from EDP Sciences database, as well as other publishers participating in CrossRef Cited-by Linking Program. You can set up your personal account to receive an email alert each time this article is cited by a new article (see the menu on the right-hand side of the abstract page).

Cited article:

Investigation of chips morphology after turning of materials applied in aerospace industry

Marek Rybicki, Piotr Szablewski

MATEC Web Conf., 121 (2017) 03020

Published online: 2017-08-09

DOI: https://doi.org/10.1051/matecconf/201712103020

This article has been cited by the following article(s):

Comparative Assessment of Tool Wear and Surface Topography After Superfinish Turning of Inconel 718 with Carbide and Ceramic Inserts

Piotr Szablewski, Stanisław Legutko, Nicolae Ungureanu, Jana Petru, Krzysztof Smak and Bartłomiej Krawczyk
Applied Sciences 15 (8) 4265 (2025)
https://doi.org/10.3390/app15084265

Tribological behavior of Inconel 718 alloy when cutting with a carbide insert prepared using the SPS technique under dry and lubricated sliding conditions

Piotr Szablewski
Tribology International 199 109951 (2024)
https://doi.org/10.1016/j.triboint.2024.109951

Evaluation of the Influence of the Tool Set Overhang on the Tool Wear and Surface Quality in the Process of Finish Turning of the Inconel 718 Alloy

Krzysztof Smak, Piotr Szablewski, Stanisław Legutko, Jana Petru, Jiri Kratochwil and Sylwia Wencel
Materials 17 (18) 4465 (2024)
https://doi.org/10.3390/ma17184465

Surface Topography Description after Turning Inconel 718 with a Conventional, Wiper and Special Insert Made by the SPS Technique

Piotr Szablewski, Stanisław Legutko, Adrian Mróz, Dariusz Garbiec, Rafał Czajka, Krzysztof Smak and Bartłomiej Krawczyk
Materials 16 (3) 949 (2023)
https://doi.org/10.3390/ma16030949

Investigation of the Influence of Anti-Wear Coatings on the Surface Quality and Dimensional Accuracy during Finish Turning of the Inconel 718 Alloy

Krzysztof Smak, Piotr Szablewski, Stanisław Legutko, Bartłomiej Krawczyk and Edward Miko
Materials 16 (2) 715 (2023)
https://doi.org/10.3390/ma16020715

Evaluation of the topography and load capacity of cylindrical surfaces shaped in the process of finish turning of the Inconel 718 alloy

P. Szablewski
Measurement 223 113749 (2023)
https://doi.org/10.1016/j.measurement.2023.113749

Fachri Koeshardono and Aep Baihaki
2193 030011 (2019)
https://doi.org/10.1063/1.5138315

Microstructure characterisation of Inconel 718 after laser assisted turning

Tadeusz Chwalczuk, Damian Przestacki, Piotr Szablewski, et al.
MATEC Web of Conferences 188 02004 (2018)
https://doi.org/10.1051/matecconf/201818802004

An Investigation of Tool Performance in Interrupted Turning of Inconel 718

Tadeusz Chwalczuk, Martyna Wiciak, Agata Felusiak, Piotr Kieruj and R. Das
MATEC Web of Conferences 237 02008 (2018)
https://doi.org/10.1051/matecconf/201823702008

Experimental Investigation and Performance Analysis of Ceramic Inserts in Laser Assisted Turning of Waspaloy

Martyna Wiciak, Tadeusz Chwalczuk, Agata Felusiak and R. Das
MATEC Web of Conferences 237 01003 (2018)
https://doi.org/10.1051/matecconf/201823701003