Issue |
MATEC Web Conf.
Volume 149, 2018
2nd International Congress on Materials & Structural Stability (CMSS-2017)
|
|
---|---|---|
Article Number | 01047 | |
Number of page(s) | 5 | |
Section | Session 1 : Materials & Pathologies | |
DOI | https://doi.org/10.1051/matecconf/201814901047 | |
Published online | 14 February 2018 |
Some physical properties of the date palm stem
1
Wood Science Laboratory, Mohammed V University in Rabat, Faculty of Science, PO Box 1014, Rabat, Morocco.
2
National Institute of Archaeology and Patrimony Sciences, PO Box 6828, Rabat, Morocco.
3
Forest Research Center, PO Box 763, Agdal, Rabat, Morocco.
The main objective of this study was to test some technological performances of date palm stem (Phoenix dactylifera L.) from the region of Marrakech in Morocco with a view to its use in housing construction in southern Moroccan regions. Physical characteristics were determined according to French AFNOR standards. The samples used were respectively 20 mm × 20 mm × 20 mm in the longitudinal, radial and tangential directions. All the results obtained were the average of the measurements on 50 samples. The results obtained showed that the moisture content has an average value of 15 % at the center of stem and 18 % at the periphery and the infradensity has a value of 0.18 g / cm3 in the center and 0.42 g / cm3 in the periphery. For samples from the center, the tangential, radial and longitudinal shrinkage were respectively 2.02 %, 1.77 %, and 0.42 %, while on the periphery of the stem the tangential, radial and longitudinal shrinkage were respectively 3.41 %, 2.98 % and 0.34 %. These results showed that the stem center has better dimensional stability compared to the peripheral region of the stem.
Résumé
L’objectif principal de cette étude était de tester quelques performances technologiques de la tige du palmier dattier (Phoenix dactylifera L.) de la région de Marrakech au Maroc en vue de son utilisation dans la construction d’habitat dans les régions du sud marocain. Des caractéristiques physiques ont été déterminées selon les normes françaises AFNOR. Les échantillons utilisés étaient respectivement de 20 mm × 20 mm × 20 mm dans les directions longitudinale, radiale et tangentielle. Tous les résultats obtenus étaient la moyenne des mesures sur 50 échantillons.
Les résultats obtenus ont montré que l’humidité avait une valeur moyenne de 15 % au centre et 18 % à la périphérie de la tige et que l’infradensité avait une valeur de 0,18 g/cm3 au centre et 0,42 g/cm3 à la périphérie. Au centre de la tige le retrait tangentiel, radial et longitudinal avaient respectivement des valeurs de 2,02 %, 1,77% et de 0,42% tandis qu’à la périphérie de la tige, les retraits tangentiel, radial et longitudinal avaient respectivement des valeurs de 3,41 %, 2,98 % et 0,34 %. Ces résultats ont montré que le centre de la tige présentait une meilleure stabilité dimensionnelle par rapport à la périphérie.
Key words: Date palm / Phoenix dactylifera L. / Moisture content / Infradensity / shrinkage
Mots clés : Palmier dattier / Phoenix dactylifera L. / Humidité / Infradensité / Retrait
© The Authors, published by EDP Sciences, 2018
This is an Open Access article distributed under the terms of the Creative Commons Attribution License 4.0, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. (http://creativecommons.org/licenses/by/4.0/).
Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.
Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.
Initial download of the metrics may take a while.